Update a Nursery Glider Rocking Chair

This post may contain affiliate links · This blog generates income via ads

by Christina Dennis

Update a Nursery Glider Rocking Chair by The DIY Mommy

You know the early-90’s-ish glider rocking chairs you can buy from big box stores for your nursery? The ones that are beige coloured and “blah”? We had to snap one up when our first baby was born. Do you know why? Because the thing was just so darn comfy!

With baby number two now here and with the fact that we had to move the glider to the living room due to space issues, I thought it was time to update the chair to make it more modern and fun looking.

Update a Nursery Glider Rocking Chair by The DIY Mommy

To be honest, I found this project quite challenging – a definite “labour of love”! I really like the results, though, and the hard work was well worth it.

Want to know how to update your dated glider with fabric and paint? Here’s how I did it:

Materials:

  • 2 1/2 yards of cotton decor fabric in main colour (I used Premier Prints Twill Suzani Corn Yellow – it’s that “Suzani” pattern that I loved and also used on this boutiqe blanket project!)
  • 1 yard of cotton decor fabric in contrasting colour/pattern (for sides of cushions and piping if desired)
  • piping cord
  • 2 cans paint + primer spray paint in white
  • reupholstery batting (it’s a heavy-weight, fluffy batting)
  • upholstery zippers (for back and for bottom cushions)

Directions:
Update a Nursery Glider Rocking Chair by The DIY MommyUpdate a Nursery Glider Rocking Chair by The DIY Mommy
Update a Nursery Glider Rocking Chair by The DIY MommyUpdate a Nursery Glider Rocking Chair by The DIY Mommy

Remove all of the cushions from the chair and the ottoman if you have one. Paint evenly with spray paint outdoors, following the paint’s directions. I decided to distress the paint with sandpaper, sanding all of the edges of the chair as shown above for a shabby chic effect. This works well if you’re painting over a dark coloured stain.

Update a Nursery Glider Rocking Chair by The DIY MommyUpdate a Nursery Glider Rocking Chair by The DIY Mommy

In my opinion, something that really dated the look of this glider was the rounded back cushion with the buttons. I covered the entire cushion with thick batting and squared the corners (I stuffed the corners with polyester batting to fill them out). I also cut strips for the edge of the cushion, making it have a “boxier” look. I hand-stitched the sides to the front and back loosely, just to hold it all in place over the old cushion. I repeated this process for the seat cushion.

Update a Nursery Glider Rocking Chair by The DIY MommyUpdate a Nursery Glider Rocking Chair by The DIY Mommy

Next, make some piping if desired for the edges of the cushions (I definitely wanted some on mine to define the edges and give my cushions some interest). Measure the diameter of your cushions and multiply that number by two to determine the length of piping that you need. Cut 2″ wide strips of fabric and sew them together at an angle (like the first photo above). Fold them over some piping cord and sew to secure (like the second photo above).

Update a Nursery Glider Rocking Chair by The DIY MommyUpdate a Nursery Glider Rocking Chair by The DIY Mommy
Update a Nursery Glider Rocking Chair by The DIY Mommy

Measure both of your cushions carefully and cut out the front and back pieces for each cushion based on your measurements. If you’re using a largely patterned main fabric like I did, make sure you decide whether or not you want to center any motifs on the cushions and cut accordingly! Cut the side, front and back rectangular pieces from your contrasting fabric based on the measurements of your cushions and the thickness of your cushions. For the back of the seat cushion and bottom of the back cushion you will be sewing a zipper in, so cut this piece 1 inch deeper (higher) and then cut in half lengthwise (as pictured in photo one above). Sew the piping onto the edges of the tops and bottoms of the cushions, meeting the raw edges of the piping with the raw edges of the cushion (as shown in picture two). Where the piping meets, cut the cord so that the beginning and end just meet, and ensure the fabric wrapping it is slightly longer. Then, fold one side of the fabric from right to wrong side to create a finished seam and sew down (as pictured in photo three above).

Update a Nursery Gilder Rocking Chair by The DIY MommyUpdate a Nursery Gilder Rocking Chair by The DIY Mommy

For the side pieces, start with the zipper side and sew the zipper in place – it joins the two narrower strips as shown in the first picture above. Topstitch, and then fold a scrap piece of fabric in half and sew on the wrong side against the short raw edge as shown in picture two above to create a zipper “stop” that will prevent the zipper from falling off. Now, sew these side pieces to the other front and back pieces of the cushion that you’ve cut out and have added piping to previously. I used a TON of pins for this part, and even then I found it quite difficult to get my seam at a nice location so that the stitch on the piping wouldn’t show. The corners were hard too! I did the best I could by machine, and then hand-stitched the corners and the little mistakes I had made earlier. It worked for me!

Update a Nursery Gilder Rocking Chair by The DIY MommyUpdate a Nursery Gilder Rocking Chair by The DIY Mommy
Update a Nursery Gilder Rocking Chair by The DIY MommyUpdate a Nursery Gilder Rocking Chair by The DIY Mommy

If your glider has a rocking ottoman, it’s a cinch to recover! Flip the upholstered piece over, remove the staples around the edges of the bottom covering fabric. Cut a piece of main fabric and batting about 3″ larger than the ottoman on all sides. Lay the fabric right side down on the floor, then the batting, then the ottoman (centered). Pull the fabric around and staple it down to the underside of the ottoman on all four sides, tugging gently and smoothing as you go. For the corners, I gently pleated and pulled them to create as smooth a corner as possible (as shown in picture three above). Finally, replace the bottom cover piece with staples.

Update a Nursery Gilder Rocking Chair by The DIY Mommy

Stuff the cushions into the cushion covers you’ve just made, place them on your glider and sit back to admire your work! I was general happy with my glider update. It certainly was a tough project, but it gave my rocker such a different look and it will look so sweet when we are able to put it in a nursery for my little girlie!

Update a Nursery Gilder Rocking Chair by The DIY Mommy

Since I did not go into detail on some upholstery basics for this post, you may find the following links helpful for this project:

Don’t be afraid to give this project a try! In my opinion, it’s well worth the effort and much less expensive than buying something new. Plus, it’s totally custom and you could make it match so perfectly with any nursery decor!

Linked to these link parties: Made by You Mondays at Skip to My Lou, Sundae Scoop Link Party at I Heart Nap Time, Doin’ it Yourself at aka design, DIY Project Parade at DIY Show Off

42 Comments

  1. I am looking forward to updating my glider. Did you sand the chair before painting it? Is there spray paint that will stick to varnish?

    1. Hi Jessie! I didn’t sand, but the paint + primer I used seems to stick pretty well to the varnished wood. If you’re worried about paint chipping off later (I’m not for mine because of the distressed look), I’d suggest sanding and sealing the finished project with a water based, clear sealer.

  2. I have no trouble at all believing that this was a difficult project! My Mom recently donated a very similar rocking chair to our church nursery, only the upholstery is a terrible Dusty Rose from the 80’s. You’ve inspired me to try my hand at re-covering it!

  3. Hi what premier cotton fabric zig zag did you buy from that fabric website? Do you mind giving me the link? Thank you.

  4. I enjoyed reading your creativity to up date your glider.

    However, this requires a skill. Without special skills such as pattern making and sewing, of course, we can not do it.

    Therefore, I prefer buying seat covers that are ready for use. I’m happy with this way.

    But, I really appreciate what you do.

    Upgrade glider is cheaper than buying new. With the up grade, the old seat will be new. We can save costs.

  5. You coud certainly see your expertise within the work you write.

    The sewctor hopes for even more passionate writers like you
    who are not afraid to mention how they believe. Alll
    the time follow your heart.

  6. I was in the process of planning the re-covering one of these gliders I paid $10 for at a thrift store. Daughter is pregnant and you need a nice comfy rocker to sit and nurse . My wood needs cleaned on the arm rests, especially, and after that the free standing cushions will be covered with a fleece grey and white modern pattern. I ended up with something like the chevron. So this tutorial was a timely ‘find’! Sadly I do not have the foot rest. I hope I can get the sewing machine working….it’s been a while! If not I expect I will be hand sewing it! Or maybe I can knot the edges like the fleece blankets!! Haha!

    Sally

    “my granddaughters call me Mimi”

  7. Awesome twist to the nursery glider. I love the rustic looking paint. I think this might be out of my DIY skillset, but after seeing this its worth a try.

  8. Very well done and nice modern look of the glider. I have an old glider lying around. I am not very skilled with the sewing stuff and would try to buy a ready made cushion.

  9. Yeah! Finally I’ve found an awesome post on custom cushion cover making. Btw, Nice choice! You post inspired me a lot.Keeping sharing my friend.Will try it definitely for mine!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.